We made super hi-end audio affordable We made super hi-end audio affordable
What's NEW ?? ( updated on 1 Mar 2010)
Our new USB-DAC series with 1x sampling rate introduced on Mar 2010, 3 different models combine with 3 different tube upgrade option, which adds a total of 12 different models to our DAC family, incredible bang-for-buck price tag, check out our DAC section for more details.
We have new design and manufacturing break though since the year end of 2008, all our new products has further enhanced and improved design on the sonic performances, further lowering of the noise floor, enhanced musicality as well as strengthened internal architectures. We call this "Mark II" design which distinct from our previous produced products. Any previous products before 2009 can bring in for new "Mark II" upgrade, cost vary with different level of upgrades..
For phono pre-amp ,our new design have 5 different MC gain settings instead of 2, and further lower in noise level for both MC and MM due to new circuit design and constructions . Which can easily surpass any other manufacturer's high-end tube phono pre-amp with just a fraction of their price. For P-105, the RCA and XLR output impedance can even lowered to 200ohm , so driving any 600ohm XLR input is surely no problem at all. We also offer a NEW designed MC/MM phono P-001 with unbelievalbe bang-for-buck promotional price.
On the year start of 2010 , we offer a totally new phono circuit which have superb MC and MM quality but with lower manufacturing cost , so we can integrate this new phono stage into whatever model of products to make it LP compatible in order to adapte the growing community. An MC+MM embedded phono stage start from only C$480 !! The sonic performance can easily outperformce those commercial available models selling around $2-4K. In home auditon is now possible with our outboard version.
From the year of 2009, we had designed several "Budget" version of Hybrid amplifier to serve even wider group of audiophiles, which is semi PCB and semi handwired just to cut the manufacturing cost, they are 25W and 70W per channel respectively, check out the Hybrid amp section for more details.
For pre-amplifier, we have a new break through in our singled-end and balanced amplification circuit, which can accept much higher input signal levels , with super big dynamics and super high density sound but still maintain a very sweet and smooth charactieristics of our original tube designs, much lowered output impedance with better bass control and punch , at the same time with ultra transparent and smooth sounding as well as sweet and tender tonal quality. Those new designs are all implimented in our new QA-8001 model. Check it out in our pre-amplifier section. This new technology can even transplant into whatever model of our pre-amplifiers with a very reasonable cost. We also introduce different levels of upgrades for different models. Each level of upgrade can futher boost the performance of the unit which you will definitely need to spend thousands to get from other manufacturers. Some of the higher models can even have FREE level 1 upgrade when new order placed.
All new Mk2 design pre-amp come with our newly design water proof volume control pot, which eliminate any oxidation contact problem of the viper and carbon film inside the pot, it is also infinite steps design, not being limited in step resolution as those so called hi-end step volume control.
We also developed a totally state-of-the-art microprocessor controlled high tech volume pot, which comes with digital display for volume level with 100 micro step resolution, you can also select between the mode of " Dual Volume "; or " Volume + Balance ". This ultra new design make the music signal pass thru only one fixed resistor , and no need to pass any solid-state device or contact points (those hi-end step volume control need to pass at least two contact points), and the sound quality is so pure , natural and open like no volume pot at all . Any model of our gear can install this optional ultra-hi-end volume control for a cost of even lower than some hi-end step volume controls. DIY customer can order this volume pot as modules to put into their own gears for performance upgrade.
The most exciting announcement is our 300B pre-amplifier, which is the Mk2 design of our previous 300B pre-amp, no more battery needed, super low noise and super high dynamics with the original 300B's sweet , tender and smoothy silky characters, we offer both RCA only or XLR+RCA input/output versions to fit your most critical requirements. They are built with all point-to-point hand wires with "ORGANIC" design, all precisely fine-tune and calibrated to the highest musical and technical requirements, which offer the biggest benefit to our customer in both price and performance over other competitors. Ready for auditions, check our pre-amp section for more details.
For
power amplifier, we have our new 300B high power output series, the first model
available is SE-300B-70W (with un-believable low price tag of C$2,680 only)
, check out our signle-ended amplifier section for more details, this is the
best chance ever to have a single-ended 300B power amp without the limitation
of the driving capabilities, no need to hunt for high-efficiency speakers which
cost arms and legs and might even have handicapped frequency response. The SE-300B-70W-Bal
and more powerful SE-300B-100W is also ready to go.
We have new chassis option for the year 2009, super high gloss solid-oak piano finish is available for our products. Now you can own a world class sound quality product with super elegant out-look with just a very reasonable increment in cost.
We are running out of showroom space for our new products , so those used trade-in gears and other pre-owned gears will sell with super discounted price as clearance just to move it out, all those items are open to best reasonable offers , large quantity discount apply to all items.
We also offer some of our designs in semi-assmebly format (PCB based model only) , just for some DIY or OEM customers to integrate our design into their own works, in order to save their project developement time and have our quality assurance. We will also take any microprocessor based software and hardware product design and manufacturing works for any company, which they don't want to do the design or manufacturing by themselves, including robotic and industrial control, software programming, automatic test equipment design....etc.
One of the reasons which we always do our best to improve our old designs, is to distingish those big names or other unauthorized duplicators from our real high-quality products with a even bigger performance gap, we usually upgrade our products just at cost when new orders being placed, for higher models, we even give free upgrades to new orders in order to give further satisfactions to our valuable customers.
(updated 26 Jan 2010)
1996-2010 All rights reserved